對於新買的焦化好色先生在线观看需要進行磨合再投入使用，在磨合過程中主要是保證潤滑劑、軸承等能夠適應後麵的持續運行。下麵小編就來向大家介紹好色先生在线观看的磨合相關知識：

The newly purchased coking generator set needs to be run in before it is put into use. In the process of running in, it is mainly to ensure that the lubricants and bearings can adapt to the subsequent continuous operation. The following editor will introduce the running in knowledge of generator sets to you:

1、空載好色先生在线观看，按前方法進行認真檢查，各方麵均很正常後，即可啟動機組。機組啟動後，將轉速調整至怠速，運轉10分鍾。並檢視機油壓力，傾聽焦化機運轉聲響，然後停車。

1. The no-load generator set shall be carefully checked according to the previous method. After all aspects are normal, the unit can be started. After the unit is started, adjust the speed to idle speed and run for 10 minutes. Check the oil pressure, listen to the running sound of the coking machine, and then stop.

2、打開汽缸體側蓋板，用手觸摸主軸承、連杆軸承等處的溫度，要求不應高於80℃,即不太燙手為正常，並觀察各機件運轉情況。若各機件溫度及結構均正常之後，再按下述規範繼續進行磨合。

2. Open the side cover plate of the cylinder block, touch the temperature of the main bearing, connecting rod bearing, etc. by hand, which should not be higher than 80 ℃, that is, it is normal if it is not too hot, and observe the operation of all parts. If the temperature and structure of all parts are normal, continue to run in according to the following specifications.

3、發動機的轉速由怠速逐步升高至額定轉速，高空載轉速運轉時間應不超過5-10min。在磨合期間，冷卻水溫應保持在75-80℃，機油溫度不應高於90℃。

3. The engine speed gradually increases from idle speed to rated speed, and the operating time at high no-load speed shall not exceed 5-10min. During running in, the cooling water temperature shall be kept at 75-80 ℃, and the engine oil temperature shall not be higher than 90 ℃.

4、在使用過程中，由於冷卻係統結構的限製，工作負荷及轉速的變化，環境溫度的改變等因素，使焦化機工作溫度的變化範圍很大。實踐表明，冷卻水溫度控製在75~85℃，潤滑油溫度在75~95℃時為有利。

4. During use, due to the limitation of the cooling system structure, the change of the working load and speed, the change of the ambient temperature and other factors, the operating temperature of the coking machine varies widely. Practice shows that it is advantageous to control the temperature of cooling water at 75 ~ 85 ℃ and the temperature of lubricating oil at 75 ~ 95 ℃.

這裏小編再次提醒下大家新買的焦化好色先生在线观看一定進行磨合後再投入使用。您想了解更多相關內容就來好色TV下载安装網站http://www.dabenche.com谘詢看看吧。

Here, Xiaobian reminds you again that the newly purchased coking generator set must be run in before it is put into use. If you want to know more about it, please come to our website http://www.dabenche.com Let's consult.